CCCUK logo

 Ian Allan Motors

Website Control

Recent threads

New Forum Posts

» Help with newly acquired 72 350 Auto by vet80y on Sun 16 Dec 18 07:40

» AMERICAN SPEEDFEST 7 on 1st - 2nd JUNE 2019 by Blackadder on Sat 15 Dec 18 22:33

» Tesla Pick Up by Jack Cooper on Sat 15 Dec 18 21:46

» Fuse replacements by Daytona Vette on Sat 15 Dec 18 13:29

» wet carpets by kentvette on Sat 15 Dec 18 09:24

» Another day, another Mid-Engine Corvette thread by Norm on Fri 14 Dec 18 23:31

» Once A Vette Head - Always A Vette Head! by Jimbo64 on Fri 14 Dec 18 20:40

» Insurance recommenations by BlackZeD on Fri 14 Dec 18 20:31

» 2007 C6 Z51 BX08 ECV - Any Former Owners Here? by Atomic UK on Fri 14 Dec 18 16:44

» South Central Midlands Supper Club Meet by Daytona Vette on Fri 14 Dec 18 11:58

» 2002 C5 Coupe by roppa440 on Fri 14 Dec 18 10:29

» CCCUK West Sussex Xmas meeting tonight 13th December by Sea5 on Thu 13 Dec 18 17:14

» Outer Door Handles by kentvette on Thu 13 Dec 18 11:13

» How Many Miles Does Your Corvette Get Driven? by Skoosh1970 on Thu 13 Dec 18 11:08

» What did you do with your Vette today? by roscobbc on Wed 12 Dec 18 12:09

» Website Copy and Paste by Rich on Wed 12 Dec 18 07:51

» Trimmer/upholsterer by Forrest Gump on Tue 11 Dec 18 20:06

» Bloodhound SSC by Atomic UK on Mon 10 Dec 18 13:04

» Spotted C2 by Jan25 on Mon 10 Dec 18 09:01

» Facebook page by fat_jogger on Sun 09 Dec 18 19:36

» O.m.g. by Redlevel on Sun 09 Dec 18 17:35

» C5 Harmonic balancer wobbling! by therabster on Sat 08 Dec 18 22:02

» My C8 Grump by Vetteheadtony on Sat 08 Dec 18 13:05

» C7 Z06 by MShaky on Fri 07 Dec 18 15:17

» Replacement head unit for US spec C6 by Young Bill on Fri 07 Dec 18 10:10

» Kelsey Hayes Aluminum Wheels by Daytona Vette on Thu 06 Dec 18 01:05

» Thames Vally Region trip to Studio 434 by Nicetie on Wed 05 Dec 18 22:33

» C6 LED halos by autocolor on Wed 05 Dec 18 19:20

» 2007 C6 ZO6, Manual. by Fraser on Wed 05 Dec 18 15:50

» 2019 Nationals by curious bystander on Wed 05 Dec 18 11:15

Steering Wheel Position Sensor - Reset?


Go to page: 1, 2 / Next


Reply to topic
View previous topicEmail to a FriendPrinter FriendlyView next topic

Author

Message

Le Vette

Regional Rep

Fri 05 Jan 18 17:58

Steering Wheel Position Sensor - Reset?


Just had steering rack removed for new harmonic balancer install. However, mechanic was unaware of need to not move the steering wheel when column disconnected from rack! So now I'm getting a message to say that the "active handling is warming up" and this won't go away, due to the swps thinking that the wheels aren't pointing forwards.

Does anyone know if it's possible to tell the swps that everything is now ok and it can forget what it knew? Maybe the message goes away after a number of successful journeys?

Can anybody throw any light on this....?

Thanks in anticipation Thumbs up [/quote]


--------------------
Peter Sansbury
CCCUK International Rep


May the Force be Quite a Long Way Behind You

Reply with quote

eurovettes

CCCUK Supporting Vendor

Fri 05 Jan 18 20:33

Re: Steering Wheel Position Sensor - Reset?


If you have access to a tech 2 then you can see the counts on the SPS, then re-align accordingly - I think it has to go to zero but cant remember

I would guess a google search may reveal some interesting videos (do use sexy words !!!)

cheers
keith

Reply with quote

eurovettes

CCCUK Supporting Vendor

Fri 05 Jan 18 20:43


ooops I meant DONT use sexy words

Reply with quote

CUSTOM EXOTICS

Addict

Sat 06 Jan 18 16:05

Re: Steering Wheel Position Sensor - Reset?


Please be ultra carefull here as damage can be done to the airbag ribbon connector at the steering wheel if rack has been reftted off centre take care back to mechanic and get him to refit should not need resetting if installed back correctly


--------------------
nothing to prove

Reply with quote

roppa440

Club Member

Sun 07 Jan 18 16:08

Re: Steering Wheel Position Sensor - Reset?


CUSTOM EXOTICS wrote (View Post):Please be ultra carefull here as damage can be done to the airbag ribbon connector at the steering wheel if rack has been reftted off centre take care back to mechanic and get him to refit should not need resetting if installed back correctly

My thoughts exactly.

Just disconnect it again and center the steering wheel.

Reply with quote

Le Vette

Regional Rep

Thu 18 Jan 18 14:35

Re: Steering Wheel Position Sensor - Reset?


The problem is that the steering wheel IS centered, however when disconnected from the rack it spins freely BUT there is only one position where it is 'right'. I have borrowed a 'fancier than normal' OBD2 reader (Autel MOT Pro) and discovered that you can get a live reading of the analog voltage being monitored by the steering wheel position sensor. Apparently, 2.5v is what should be read when the steering wheel is in the 'right' position (changes by approx 1v per revolution).

Now I'm beginning to sound like an expert I'll defer from posting any more until I try and reposition the steering wheel vs the steering rack tomorrow, using the 2.5v perceived wisdom... here's hoping, fingers crossed. Scratchchin


--------------------
Peter Sansbury
CCCUK International Rep


May the Force be Quite a Long Way Behind You

Reply with quote

Rich

Club Member

Thu 18 Jan 18 16:20

Re: Steering Wheel Position Sensor - Reset?


Good luck, Pete.


--------------------
Rich Rogers
CCCUK Lifetime Member
2017 Yellow SS Camaro

Reply with quote

Le Vette

Regional Rep

Fri 19 Jan 18 17:21

Re: Steering Wheel Position Sensor - Reset? Message Icon


OK, so that plan didn't work. Couldn't successfully read the voltage from the SWPS using the gizmo, but of course it worked fine once I got home and tried again! Grrr.

Oh, and I also have a B0026 DTC code ("Driver Frontal Deployment Loop Open Circuit") which I'll need to understand better before I do any more... Banghead

Tomorrow is another day. Rolling Eyes


--------------------
Peter Sansbury
CCCUK International Rep


May the Force be Quite a Long Way Behind You

Reply with quote

Le Vette

Regional Rep

Wed 24 Jan 18 16:10

Re: Steering Wheel Position Sensor - Reset?


OK, an update:

Re-tried the OBD2 reader on the steering wheel position sensor - it turns out that the engine must actually be running to get a valid voltage reading from the SWPS. Once the engine is running you can disconnnect the steering column from the rack at the knuckle joint under the hood and turn the steering wheel until you get a reading of around 2.4 volts. Your steering wheel is then correctly centred. Thumbs up

The remaining airbag problem (B90026 DTC) is probably a result of damage inflicted on the clockspring located directly behind the steering wheel and airbag. Apparently if you turn more than three revolutions you can break this, so we have another on order.... N.B. when replacing this item there is a very similar centering process as when you disconnect the other end of the column! Basically you have to leave the steering wheel centred and make sure you put it all back in exactly the same position.

I'll update this thread again once we are in a position to say for sure what the problem with the airbags circuit is...



Last edited by Le Vette on Wed 24 Jan 18 16:27; edited 1 time in total. [5 %]
--------------------
Peter Sansbury
CCCUK International Rep


May the Force be Quite a Long Way Behind You

Reply with quote

CUSTOM EXOTICS

Addict

Wed 24 Jan 18 16:32

Re: Steering Wheel Position Sensor - Reset?


Ps I actually have a working c5 corvette clock spring here if it helps second hand if ur local to me feel free to collect


--------------------
nothing to prove

Reply with quote

Reply to topic
View previous topicEmail to a FriendPrinter FriendlyPrivate MessengerView next topic

Go to page: 1, 2 / Next


Permissions

You cannot post new threads in this forum
You cannot reply to threads in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot add events in this forum
You cannot attach files in this forum
You cannot download files in this forum